A tail fan to spin the generator around lining it up with the wind’s direction must be attached to the 12″ nipple at the back of the bracket. Cut a fan out of old tin siding or roofing with tin snips or a cutting torch. A right angle triangle shape works best. Drill three holes in the nipple. Use self-tapping screws (steel roofing screws work good) to affix the tail to the nipple.
(See photo)
 Tower/Pole – I used an old Television antenna tower 20′ tall with a 2-1/2″ diameter pipe top piece. You’ll also need a Stop at the top of the tower which lines up with the Stop on your bracket assembly. This can be welded or bolted onto the tower. The Stops will only allow the generator to turn 360° clockwise andcounterclockwise so your cable doesn’t get twisted around and around the pole/tower.


A joint of 2-3/8″ oil field tubing anywhere from 10′ to 20′ in length (height) attached to a building or bolted to your truck bumper makes a good tower. Make sure it is secure and you may need to use guy wires. If you aren’t sure how to mount the generator, send me a message and I’ll try to help.

Fan Clutch to Alternator Attachment:

The fan clutch hub can be welded directly to the alternator hub, just make certain the fan is perfectly straight in line with the alternator shaft. Make sure the alternator’s built-in wire plug ins are located on what will be the bottom of the generator. If you don’t have access to a welder, create a union from the 3″ washer and four bolts, which will fasten the two major components together. Drill four holes to match the holes in the fan clutch. Use a 1/4″ tap to cut threads in the holes. Unscrew the alternator pulley nut, remove the pulley and small fan. Slide the union over the alternator shaft—bolts pointing away from alternator, then reattach the alternator fan and nut onto the shaft (leave pulley off). The large nut will hold the union in place. Attach the fan clutch assembly to the bolts now protruding from the alternator. Tighten nuts with lock washers in place.
You’ll need:

3″ washer, 3/16″ thick, 5/8″ hole.
Electric drill
1/4″ steel drill bit
1/4″ thread tap
1/4″ X 1-1/2″ to 2-1/2″ bolts (4) and lock washers (4)

(To determine length of bolts, stack the fan on top of the alternator with both shafts in line, fan pulley on alternator pulley. Measure length along the two shafts from back of alternator fan to back fan clutch hub. Use this length for the bolts.)


Once you have all the generator components fastened together, mount it on your pole or tower. Insert the pipe on the generator inside the larger pole pipe (or the top of your tower). Use two steel washers together to create a bearing between the generator and tower for a smooth surface for the generator to pivot 360 degrees. Attach the positive and negative wires to the alternator and secure with zip ties, baling wire and/or duct tape on the bracket and along the tower. It isn’t really homemade unless it has a little baling wire and duct tape on it somewhere, now is it?! You’ll need assistance standing the tower and generator upright as it will be pretty heavy. Ropes and a come-along will help if you’re going up fairly high. If it’s always windy in your location, you only need to be high enough off the ground to keep the moving parts safely overhead. Securely fasten your tower in place. The wind can be deceptively strong so do not cut corners on this final assembly stage.

Now that you’ve erected the wind generator connect the wires to your battery(ies) with a charge controller in between to prevent over-under charging. Now you’re ready to hit the lights, crank up the jams and bust out those old disco moves I know you’ve been saving up for an electric slide on the beach with your family and friends.

Build and use at your own risk. My generator works fine but you are responsible for your work. Good Luck and Power Up!

Source: motherearthnews.com.

  Page Turn  


Related articles in DIY